DIY Audio Projects Photo Gallery
 NEW    Bruce Heran outlines the details and construction of his simple DIY 6DJ8 (ECC88) Tube Hi-Fi Headphone Amplifier Project.

DIY Audio Projects Photo Gallery


[ Gallery Home | Upload Photo | Recent Uploads | Most Viewed | Search ]


Low-Inductance-DIY-Speaker-Cable.jpg
Low-Inductance-DIY-Speaker-Cable.jpgDIY Low-Inductance Speaker Cables7726 viewsSimple cable design that uses four 16 gauge wires which result in an equivalent 10 AWG cable. The wires are twisted together in opposite directions which helps keep inductance of the overall speaker cable to a minimum. See the Low-Inductance DIY Speaker Cable project page for full details.
Silver-Copper-RCA-Audio-Cables.jpg
Silver-Copper-RCA-Audio-Cables.jpgSilver / heat shrink braided RCA cables with Copper drain8979 viewsA few years back I made some pure silver braided RCA cables where the third wire is not terminated at the destination end . The silver is polished then covered in heat shrink. There are two earth or negative wires. Theory is the third wire drains noise back to the source. In this build all those principals are used except the second earth wire is .8mm enameled copper wire. Smaller ferrite chokes were also used. I made these yellow to distinguish them from others. These are only 400mm long for phono preamp to preamp interconnect. Gold plugs and silver solder were used. Sound good.

diy-cat5-speaker-cable.jpg
diy-cat5-speaker-cable.jpgDIY CAT5 Speaker Cables10264 viewsDIY Speaker Cables made using Category 5 (CAT5) network wire. The Cat5 cables are braided together as shown in the photo and terminated using banana plugs.
DIY-Interconnect-Wires.jpg
DIY-Interconnect-Wires.jpgDIY RCA Interconnect Cables9239 views24ga shielded silver plated OFC copper twisted pair with Teflon dielectric. Machined RCAs and hardware are from surplus auto interconnects. Including TechFlex and heat shrink, these cost under five bucks.

Related: DIY RCA Silver Interconnect Cables
mURI_temp_f1d472f0.jpg
mURI_temp_f1d472f0.jpgDIY Speaker Cable6029 viewsThe cable in the beginning of the project.
mURI_temp_630f4f06.jpg
mURI_temp_630f4f06.jpgDIY Speaker Cable5432 viewsThis is DIY Speaker Cable that I made for a friend.
This is the regular twisted pair design with the double shielding. I've used the regular heat shrink tube for the primary shield and nylon braided sleeve for the secondary shield.

The ends are terminated via plastic banana pins.

Also, here is a pair of DIY Braided Speaker Cables that I made.
mURI_temp_e4a2b45b.jpg
mURI_temp_e4a2b45b.jpgDIY Speaker Cable - Twisted Pair Design6224 viewsThis is DIY Speaker Cable that I made for a friend.
This is the regular twisted pair design with the double shielding. I've used the regular heat shrink tube for the primary shield and nylon braided sleeve for the secondary shield.

The ends are terminated via plastic banana pins.

Here are my DIY Braided Speaker Cables.
DIY-Silver-Wire-RCA-Interconnect-Cables.JPG
DIY-Silver-Wire-RCA-Interconnect-Cables.JPGDIY Interconnect Cables with Silver Wire6242 viewsSimple DIY RCA interconnect cable project made using pure silver wire.

Related: DIY Silver RCA Interconnect Cables
DIY-Audio-Silver-Wire-RCA-Interconnect-Cables.JPG
DIY-Audio-Silver-Wire-RCA-Interconnect-Cables.JPGDIY Audio Silver Wire RCA Interconnect Cables7131 viewsSimple DIY interconnect cables made with silver wire.

Related: DIY RCA Silver Interconnect Cables
Cotton-ConneX-DIY-Interconnect-Cables.jpg
Cotton-ConneX-DIY-Interconnect-Cables.jpgCotton and Silver DIY Interconnect Cables8846 viewsThese are the Cotton ConneX DIY Interconnect Cables which are very similar to the DIY Silver Interconnect Cables. The Cotton ConneX are solid Silver wire with Cotton insulation. These were hard to make as the cotton continues to fray. These were well worth the effort as the produce a different and enchanting cable.
DIY-Speaker-Cables.jpg
DIY-Speaker-Cables.jpgSimple DIY Speaker Cables8111 viewsThese are simple DIY (do-it-yourself) speaker cables that I made from braiding copper strand wire. I use these cables with my DIY Hi-Vi 3-Way Tower Loudspeakers
 
11 files on 1 page(s)


DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Opamp Projects :: DIY Phono Projects :: DIY Cable Projects :: HI-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy