DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 05 Dec 2019, 12:14

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 2 posts ] 
Author Message
 Post subject: 2a3 single ended
PostPosted: 29 Oct 2019, 01:53 
Offline

Joined: 28 Oct 2019, 04:54
Posts: 2
Hi,
I want to build this http://diyaudioprojects.com/Schematics/ ... ematic.htm
How do i power the second channel, from the same point of channel one, or how!?
Thanks!


Top
 Profile  
 
 Post subject: Re: 2a3 single ended
PostPosted: 23 Nov 2019, 14:26 
Offline

Joined: 16 Sep 2017, 00:35
Posts: 1
This is clearly intended to be a stereo amplifier because the power supply shows 2 individual DC heater supplies for 2 2a3 tubes and the EF86 heater supply shows 2 heaters in parallel.

I believe the intent is that you make the second channel and simply attach the B+ to the same pole of the switch S2 as the first channel.

Also note that the switch S2 is important. The idea is that you flip the main power switch and allow the heaters to warm up first. And then after a minute or two, you flip the main B+ switch. This helps prevent cathode stripping and helps your tubes last longer.

I would also change this design a bit.

1: The power supply transformer IMO is a bit weak. A full bridge rectifier with a capacitor input will only provide ~62% of the AC current rating of the transformer. This is just enough current for all the bias currents of the tubes. In a class A SET amp, the average currents will be close enough to the bias current that this kind of approach would work. But usually what happens is that if your amp tries to draw large peak current, the PSU struggles to keep up and your B+ voltage will sag. It isn't the end of the world if you build a PSU like this, but I think upping the current spec on the transformer will help the amplifier's transient response. Thats my 2 cents at least.

2: You will also have a fair amount of cross talk with a design like this. Both the right and left channel will share the same PSU cap for the 2a3. I would probably add a RC filter after C8 and split the PSU rails so that you have individual PSU rails for right and left channel. This will give you much better channel separation.

3: I highly doubt its necessary to DC heat the EF86 tubes. I would try AC heating them first. You can always DC heat later on if its necessary.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: Don F, Google [Bot] and 17 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy