DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 24 Oct 2020, 16:03

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: 07 Feb 2020, 18:51 
Offline

Joined: 07 Feb 2020, 18:29
Posts: 2
Hi!

I am new to this forum but i am very passionate about audio, especially vacuum tube amplifiers. I own a Decware Taboo MKIII tube headphone amp, connected to a Khadas Tone Board DAC, a USB isolator and to my PC. As headphone i am using the Fostex TH-X00. Currently installed vacuum tubes are rectifier: Svetlana 54ug black plate '50 signal tubes: 2x Hungarian Tungsram EL84 and as input: Siemens silver plate '60 E88CC.

Anyway, when looking for tubes, especially in ebay often in the describtion they put test results of the tube. I just bought 2x Philips SQ E88CC Herleen factory the sellere shared these test results: Tested on ELPO P-508 - Pair = 11/10 + 11/11 mA!

I asked the seller what the measurements mean and his answer was "hese are the currents after measurements, the maximum cathological values ​​are 14 mA, the lamps are not NOS but in a nice condition".

I am wondering do these values have any impact on the sound? I asked the seller and he responded "There is no difference for these tubes ..., e.g. the Soviet equivalent of 6n23p sounds great even at 4-5mA :)"

But i'd like to fact check that.

Can anyone confirm this?

And how do these values concern me as a buyer?

Also i'd like to know how to the Philips compare to the siemens?

My best regards and thanks a lot

Yoshi


Top
 Profile  
 
PostPosted: 18 Feb 2020, 03:03 
Offline

Joined: 23 Feb 2017, 02:02
Posts: 677
Unless the circuit requjres a matched valve, otherwise most circuits don't require matched valves.

A non matched and weak valve with high quality hifi construction will sound better than a non hifi valve perferctly matched.

Also majority of the time you recive the valve and the actuall matching of the valve differs from what buyer specified so is not recomended to chase highly matched valves.
Regardless of the supplyer.


Top
 Profile  
 
PostPosted: 27 Feb 2020, 14:39 
Offline

Joined: 07 Feb 2020, 18:29
Posts: 2
Hi

It isn't quite what i meant, i only have one 6922 slot.

What i meant is, when you look for tubes on ebay they mostly post measurements of emission tests for instance 16 mA/19 mA which corresponds to 106.6%/126.6% (100% is 15 mA) for Siemens E88CC tubes.

Let's that there is a second tube same everything as the first one that tests 23/22mA (153.3%/146.6%).

Would there be any sonic difference?


Top
 Profile  
 
PostPosted: 03 Mar 2020, 22:23 
Offline

Joined: 23 Feb 2017, 02:02
Posts: 677
You'd undlikley notice much diffrence, there will be a diffrence, but small.

Both channel will sound very similar unless the tubes are off by a very far ammount.
20% you will not notice any diffrence.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 16 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy