DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 21 Feb 2020, 05:24

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 232 posts ]  Go to page Previous  1 ... 20, 21, 22, 23, 24
Author Message
 Post subject: Re: "Lacewood" Amp V2.0
PostPosted: 08 Jan 2020, 17:23 
Offline
Project Author
User avatar

Joined: 06 Jun 2008, 18:23
Posts: 5174
Location: Australia
john55 wrote:
My wife turned up with a 1947 Marconiphone radio the other day. She thought I might want to try to get it working.
I don't have much interest or knowledge in radio but decided to give it a look over. I managed to salvage the little mono amp that I can play with later, but as for the receiver..... I didn't have a chance (I don't know about the USA but here in Spain I don't think anyone broadcasts on SW / MW / LW anyway).
Then I looked at the case, dull brown bakelite but not a scatch or crack on it anywhere. A bit of soapy water and dasboard polish and look what I've got.
This is going to house the 6V6 and tone stack that I've been asking questions about in the last two or three posts on this thread. It might be a bit of a squash but I've got height as well as width and depth. Any thoughts?

Looks good.

_________________
Projects:”Image” - Low Profile 100W Class D amp | ”fiih” - 150W Holton inpsired power amp | "Precision" - 300W Class AB Holton power amp | ”Gothic” - FET Push-Pull headphone amp


Top
 Profile  
 
 Post subject: Re: "Lacewood" Amp V2.0
PostPosted: 13 Jan 2020, 12:22 
Offline

Joined: 13 May 2016, 02:02
Posts: 133
Location: Javea, Spain
This chassis is a bit tight to fit everything, but that's all I've got if I want it to fit in the Marconiphone case.
I've kept the two 12AU7's and the 6SN7 as far away from the mains transformer as possible. Are they far enough away or am I asking for problems?
I would prefer to keep the 32uF+32uF capacitor on the top plate if possible but could move it underneath if the heat from the 5U4GB and the 6V6 on either side of it would cause problems. Asking for advice here as I have read that capacitors don't like heat.


This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.



Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 232 posts ]  Go to page Previous  1 ... 20, 21, 22, 23, 24

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: Google [Bot] and 15 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy