DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 11 May 2021, 09:10

All times are UTC - 6 hours [ DST ]

Post new topic Reply to topic  [ 3 posts ] 
Author Message
PostPosted: 03 Sep 2019, 22:02 

Joined: 23 Nov 2018, 19:41
Posts: 9
I'm beginning to explore designs for a push-pull power amplifier with two pentodes as the output stage. Having looked at many schematics online, I've noticed a variety of bias strategies ranging from self-bias, mixed fixed / self bias, and fixed bias output stages. I have some questions relating to some of the practical implications of each strategy. More specifically, I'm interested in implementing a self-biasing scheme. My questions are

1) How important is it to have a "matched pair" of tubes for each output channel?

2) If I choose to use a matched pair of tubes, what type of adjustment mechanism do I need in place to ensure that the tubes have the same quiescent bias point? Should I put a trimpot in series with the cathode resistor for each tube so that I can adjust the tubes to have the same quiescent cathode voltage?

3) In the contest of a stereo amplifier (as opposed to a guitar amp), is there a hard logic to using fixed-bias v self-bias?

A final unrelated question: what do black glass tubes look like when they're illuminated? I've found some cheaper Russian tubes which feature black-glass envelopes.

PostPosted: 04 Sep 2019, 02:07 

Joined: 23 Feb 2017, 02:02
Posts: 677
As long as the valves are within 10% no more than 20% diffrent in the idle current inside amp.
Then its good enough.

Diminishing returns for being more matched, you can go as far as you want with matching but it gets stupidly expensive when your already fairly matched.
And over time the mathcing drifts.

PostPosted: 04 Sep 2019, 21:44 
Project Author
User avatar

Joined: 04 Jun 2008, 20:59
Posts: 4370
Location: Arizona, USA
Hi, Generally I agree, matching is usually not required. For most purposes 10% is fine. It somewhat depends on what class of amplification you choose. If it is AB then 10% even 20% is good as the tubes are usually running at about only 30-40% of their dissipation at idle and are almost never running at anything near the max spec. If you are doing class A then you need to be careful not to exceed the ratings as they are often at 75-85% of max dissipation. A 20% error can result in either tube failure or short tube life.

Some general considerations: It is helpful to be able to test the idle current in each tube. A one ohm resistor in each cathode will measure 1 milli volt / milli ampere of current. If you use fixed bias that is adjustable for each tube separately then you can very accurately set the idle condition accurately. This does not guarantee it will match at higher power levels though. You will have to check the current from time to time. About every 6 months seems typical. I consider it quite important to be able to adjust the idle current in class A push-pull amps to protect the tubes and get the maximum output before one or the other runs out of current (horrible distortion is the result of this). These too should be checked at regular intervals. IMO an auto bias arrangement is excess complication. Using a shared cathode resistor is quite fine for nearly any PP class AB amp. As an initial project I would recommend this arrangement. Next best IMO would be fixed bias class AB. My personal opinion is that really class A push-pull has the best sound and all my designs are of this type. There are some negatives though. The largest is that the maximum output power is significantly lower. Additionally tubes run hot and overall power consumption as a ratio to output is low. To my ears all this doesn't matter as much as I like the sound class A amps can deliver. My designs all use an unconventional balance method and do not have "bias" in the normal sense. They also need to be checked about every 6 months. It is a simple task and takes only minutes. Look at a few of the projects I posted to see the details.

Good listening

Some of my DIY Tube Amplifier Projects:

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 6 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 33 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© - Terms of Service - Privacy Policy