DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 01 Dec 2020, 19:37

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 2 posts ] 
Author Message
PostPosted: 20 Oct 2020, 06:05 
Offline

Joined: 29 Sep 2020, 13:47
Posts: 2
Location: UK
Hi All,

I was wondering if people can help with a few questions, I've searched all over google for this but there seems to be limited info. I'll try and keep it short and simple

I decided to put together a tube amp, the valves are EF95/6AK5 (GE Jan 5654W, Mullard M8100 etc) running in triode mode, an op amp is then used to amplify the tube output for the headphones.
I've tried a lot of different values of components and I think I have found the sweet spot.

Info about the amp:
100VDC provided by DC booster, input voltage is 12V, oscillator runs at 75KHz using UC3843C IC, it sounds clean to me and scope shows very little ripple.
EF95 tubes running at 85V plate voltage (depending on tubes), anode resistor (3K - R7 & R8) is dropping 15V.
Cathode resistor (270 - R2 & R5) is dropping about 1.35V.

Q1
Based on ohms law, the current drawn by each tube is 5mA (1.35/270 & 15/3000), this sounds about right. Now I've followed various differnt methods for calculating the anode and cathode resistors, none of these calculations come close to producing the desired voltages.
Is this normal, I ask this because I was trying to set the bias to 1.5V but but settled on 1.35V as different tubes bias at different voltages using the same resistor.

Q2
Does it matter if I set the bias to 1V, 1.35V or 1.5V.

Q3
I'm running the plate coupling caps (C8 & C10) at 85VDC, they are rated for 100VDC and are made by TDK/EPCOS and are PET/Polyester. Will this be a problem, the voltage is stable.

Q4
I decided to add cathode bypass capacitors of 100uF (C5 & C6), is that too high or does it not matter. The audio out sounds fine to me.

Q5
People say the Russian tubes 6J1P-EV are compatible with EF95 tubes, I tried them with the current resistor values, the plate runs at 95V and the bias is less than 1V. I take it they aren't quite compatible.

Q6
I've noticed with some "matched" tubes the bias voltage is different by 0.5V, I take it the sellershop did not match the tubes?

Sorry about the incorrectly drawn tubes in the attachment, the pins are correct though.

Apologies if the questions seem stupid, any help appreciated, thanks


This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.



Top
 Profile  
 
PostPosted: 27 Oct 2020, 03:50 
Offline

Joined: 26 Nov 2019, 02:09
Posts: 13
You're questions don't seem stupid to me at all. I'll give it a try.

A1: I made a loadline for 3K and (like you) came closer to 1.5 V at Va = 85 V than to 1.35 V. But I think that the difference is too small to indicate a problem with the tubes (or something else).

A2: I'm not sure because there are different opinions on this subject when this is discussed on forums and untill now I didn't find literature in which this possible problem is quantified. I personally would not like a triode with a moderate amplification factor like the 6AK5 (mu = 28 in triode mode) to work at such a low grid voltage because a little bit of grid current will flow in the positive going parts of the input signal (true with input levels like from a CD player). The point where grid current starts is - 1.3 V (valid for almost all tube types). The amount of grid current is very small, but it varies with input (the more positive the input voltage swings, the more grid current will flow; in the negative going part of the input signal no grid current flows).

A3: At start-up the tubes are not conducting right away. Because of that there will be no voltage drop over the 3K anode resistors untill the tubes warmed up and start to pass current. So during this time the full 100 Vdc is over the coupling capacitors. Probably they will be able to stand this, but I personally would prefer a little higher maximum voltage for those capacitors.

A4: In my opinion 100 uF is fine (large enough for the low frequencies not to roll-of + no problem if the value is higher than necessary).

A5: I don't have experiences with the 6J1P-EV. The values in datasheets are valid for an average tube. The values are the result of measuring more than one specimen of the same tube type. So individual tubes can/will show a bit different values than the datasheet tells us.

A6: The bias being 0.5 V off (so per tube being about 0.25 V off) sounds like a lot to me at a grid voltage of - 1.35 V. Doesn't look like 'matched' tubes to me. But if they were realy matched, than I wonder at what working point(s) the seller (of manufacturer) matched the tubes. I think that matching tubes at a certain working point doesn't garantee that they will be matched at all other working points. In your case we're discussing a pentode connected as a triode. Maybe the matching was done with the tubes connected as pentodes.

_________________
Greetings,
Robert

http://otl800.blogspot.com/


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: Google [Bot] and 17 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy