DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 19 Aug 2018, 10:43

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 26 posts ]  Go to page Previous  1, 2, 3
Author Message
PostPosted: 03 Jun 2018, 12:53 
Offline

Joined: 11 Nov 2013, 22:35
Posts: 9
Matt,
Anymore comments on its performance or changes you would consider, now that you have lived with it for awhile?

Thanks,


Top
 Profile  
 
PostPosted: 05 Jun 2018, 19:22 
Offline
Project Author
User avatar

Joined: 06 Apr 2009, 10:08
Posts: 1446
Location: US Pacific Northwest
ToddD wrote:
Anymore comments on its performance or changes you would consider, now that you have lived with it for awhile?
Not really. I don't have any changes I'd make to the electrical design. I might make the chassis a little larger just for esthetics.

I will say that the amp plays best putting out a little volume. When that's what I want, in it goes. However, when I'm just listening quietly or for background music, I'm much more likely to be listening to my 6EM7 or Marblewood depending on the music.

I will also add that the 6336 is not a quick start kind of amp. Every 6336 I've used takes at least 5 minutes to stop "tinging" and "squeaking" (the tube not the amp) and for the sound to settle down. I think this is just a function of the size and power level of the output tube. After about 5 minutes it's all good.

_________________
Matt
It's all about the Glass!
http://www.CascadeTubes.com
Cascade Tubes Blog


Top
 Profile  
 
PostPosted: 05 Jun 2018, 19:34 
Offline

Joined: 11 Nov 2013, 22:35
Posts: 9
Matt,
I don't need another amp, but this looks like a fun amp. Most likely use in my garage system to play rock n roll, but may move it to the main room to play blues.

Probably purchase parts between now and Christmas and hopefully have a picture to add some time after that. I was also looking at the lacewood also. Right now I think I will build both in time.

Thanks for all you contribute to this website. This noob appreciates it


Top
 Profile  
 
PostPosted: 28 Jun 2018, 04:03 
Offline

Joined: 22 Feb 2017, 07:55
Posts: 11
Matt's design says 2.5K OPT for this design. I have a pair of Edcor CXSE25-5K. Can these be used here ? A parallel S.E maybe ?


Top
 Profile  
 
PostPosted: 28 Jun 2018, 18:02 
Offline
Project Author
User avatar

Joined: 06 Apr 2009, 10:08
Posts: 1446
Location: US Pacific Northwest
jocelys1 wrote:
Matt's design says 2.5K OPT for this design. I have a pair of Edcor CXSE25-5K. Can these be used here ?
The short answer is yes. I would expect about 15% to 20% less power but lower distortion.

I originally played with 1.7kΩ and 2.5kΩ because I thought that the higher impedances overly constrained the big triode. I finally settled on the 2.5kΩ as the best tradeoff between power and distortion given what I generally like. The 5kΩ outputs should be very clean but about 1dB less power (not enough to worry about, IMHO).

Let us know how it goes.

_________________
Matt
It's all about the Glass!
http://www.CascadeTubes.com
Cascade Tubes Blog


Top
 Profile  
 
PostPosted: 10 Aug 2018, 09:22 
Offline

Joined: 22 Feb 2017, 07:55
Posts: 11
Hi Matt, I'm itching to give this a go either with the CXSE25-5K I have or get the GXSE15 in your original design. Is there any way to squeeze more power out of the design ?

Will a parallel single-ended work ?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 26 posts ]  Go to page Previous  1, 2, 3

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy