DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 22 Aug 2019, 03:37

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 81 posts ]  Go to page Previous  1, 2, 3, 4, 5 ... 9  Next
Author Message
 Post subject: Re: 4S preamp project
PostPosted: 20 Nov 2018, 12:38 
Offline

Joined: 19 Oct 2018, 15:30
Posts: 132
Location: Montréal, Québec
So, if I understand, with a B+ of 250V and lets say 20mA (10mA for each LEDs), I would need a 12.5k resistor wich can dissipate 5W of power ?


Top
 Profile  
 
 Post subject: Re: 4S preamp project
PostPosted: 20 Nov 2018, 17:29 
Offline
Project Author
User avatar

Joined: 06 Apr 2009, 10:08
Posts: 1589
Location: US Pacific Northwest
Gab wrote:
So, if I understand, with a B+ of 250V and lets say 20mA (10mA for each LEDs), I would need a 12.5k resistor wich can dissipate 5W of power ?
A couple of points.

1. Put your LEDs in series. This way you're not asking the B+ supply for lots of current. Remember with vacuum tube B+ supplies voltage is cheap, current costs.

2. Unless you're looking for supplemental room lighting think more like 5ma for the LED chain.

3. So, for a 250V B+ supply; R = 250/.005 = 50kΩ. Power rating is: P = (0.005^2)*50000 = 1.25W. I'd use a 2W resistor.

Does this make sense?

_________________
Matt
It's all about the Glass!
http://www.CascadeTubes.com
Cascade Tubes Blog


Top
 Profile  
 
 Post subject: Re: 4S preamp project
PostPosted: 20 Nov 2018, 19:04 
Offline

Joined: 19 Oct 2018, 15:30
Posts: 132
Location: Montréal, Québec
Totally. Less current means less power to dissipate, less space and less costs. Is there any minimum current specs or recommendations for an led ? I didn't find any minimum spec anywhere !

Again, your answers are appreciated. It helps me a lot, especially when I look around the web and can't find exactly what I need.


Top
 Profile  
 
 Post subject: Re: 4S preamp project
PostPosted: 20 Nov 2018, 19:32 
Offline
Project Author
User avatar

Joined: 06 Apr 2009, 10:08
Posts: 1589
Location: US Pacific Northwest
Gab wrote:
Is there any minimum current specs or recommendations for an led ?
Not really.

If you are designing for mass production you need to worry about minimum current because of variability in luminous flux at low currents. My son (EE PhD specializing in MicroElectronics) rants at me about feeding LEDs with too little current and causing item to item variability.

My experience (30 years plus) tells me that a few mA is more than adequate for the vast majority of cheap red/yellow/green LEDs on the market today. If one is a little brighter or dimmer than another, I chalk it up to the unpredictability of the universe and take another sip from my beer. :beerchug:

_________________
Matt
It's all about the Glass!
http://www.CascadeTubes.com
Cascade Tubes Blog


Top
 Profile  
 
 Post subject: Re: 4S preamp project
PostPosted: 21 Nov 2018, 10:14 
Offline

Joined: 19 Oct 2018, 15:30
Posts: 132
Location: Montréal, Québec
As long as they light up bright enough to be seen, i’ll have no problem living with a couple lumens difference ! (And won’t wait for any unpredictability of the universe to have a sip from my beer ahah !)


Top
 Profile  
 
 Post subject: Re: 4S preamp project
PostPosted: 21 Nov 2018, 10:47 
Offline

Joined: 19 Oct 2018, 15:30
Posts: 132
Location: Montréal, Québec
The power supply components are installed. I ran the B+ to the signal side, but I am still thinking about the layout. The holes in the divider might be too small for all the wires I need to get through.

I also wan’t to buy terminal strips locally so I won’t have to wait for the shipping, but can’t find anything up to this point. Totally forgot to order them at the same time as my first order from Digi-Key. We are getting a lot of snow these days so going out on the road to Montreal to buy parts is out of question.


This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.



Top
 Profile  
 
 Post subject: Re: 4S preamp project
PostPosted: 21 Nov 2018, 10:49 
Offline

Joined: 20 Feb 2014, 10:35
Posts: 58
Location: NZ
Always thought LED's on tube amps are superfluous, the tube heater glow being a good indicator that the amp is 'On'.
(unless the tubes are enclosed inside the chassis).
Anyway, it is a good looking build.


Top
 Profile  
 
 Post subject: Re: 4S preamp project
PostPosted: 21 Nov 2018, 11:44 
Offline
Project Author
User avatar

Joined: 06 Apr 2009, 10:08
Posts: 1589
Location: US Pacific Northwest
Gab wrote:
I ran the B+ to the signal side
One quick note. Make sure you run the B+ power return / signal ground back through the same hole as the B+. If you don't, then the divider metal forms a closed loop conduction path link with your power supply loop. This arrangement can couple field noise into your B+ circuit.

See this shot from the Lacewood V2.0. All the B+ feeds and the ground buss penetrate the metal divider at a single place.
Attachment:
PowerFeed.jpg
This is the way to do it. :up:


This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.


_________________
Matt
It's all about the Glass!
http://www.CascadeTubes.com
Cascade Tubes Blog


Top
 Profile  
 
 Post subject: Re: 4S preamp project
PostPosted: 21 Nov 2018, 13:52 
Offline

Joined: 19 Oct 2018, 15:30
Posts: 132
Location: Montréal, Québec
Suncalc wrote:
Gab wrote:
I ran the B+ to the signal side
One quick note. Make sure you run the B+ power return / signal ground back through the same hole as the B+. If you don't, then the divider metal forms a closed loop conduction path link with your power supply loop. This arrangement can couple field noise into your B+ circuit.

See this shot from the Lacewood V2.0. All the B+ feeds and the ground buss penetrate the metal divider at a single place.
Attachment:
PowerFeed.jpg
This is the way to do it. :up:


Good to know ! Should I consider that having longer wires that run across the enclosure is better than creating this kind of loop ?


Chris65 wrote:
Always thought LED's on tube amps are superfluous, the tube heater glow being a good indicator that the amp is 'On'.
(unless the tubes are enclosed inside the chassis).
Anyway, it is a good looking build.


Thank you for your comment. The LEDs shows wich input is selected. For the "power status" LED, I consider the heater glow to be nothing more than the confirmation that the heaters are on. The heaters and power supply/B+ are two completely different circuits so it might be useful if something goes wrong with the amp. The "if" is very important in this sentence !


Top
 Profile  
 
 Post subject: Re: 4S preamp project
PostPosted: 21 Nov 2018, 16:28 
Offline
Project Author
User avatar

Joined: 06 Jun 2008, 18:23
Posts: 5126
Location: Australia
When building all my battery powered devices which require a led (always 3mm) to indicate on firstly; I like to use retro yellow (most go for blue these days but being retro, I go the old amber/yellow). Secondly I buy the highest output LEDs I can. These you can run on extremely low current and they will still glow. I like a barely "on" extremely low glow - because I don't want distraction when listening to music, always in a darkened room and in this mode they consume very little battery power.

Even my mains powered devices I have the yellow LEDs barely on. Nothing worse than a bright LED cast a searing beam across your listening area.

To sum up, high powered 3mm LEDs on extremely low current.

_________________
Projects:"retro2308" - chip based headphone amp | ”Calibre 834” - tube phono MM preamp | ”najah” - Raw 180W Tripath Class D power amp | "Icon" - Shuguang CV-181Z preamp


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 81 posts ]  Go to page Previous  1, 2, 3, 4, 5 ... 9  Next

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: Google [Bot], Google Adsense [Bot], M. Gregg and 16 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy