DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 19 Feb 2019, 19:36

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 206 posts ]  Go to page Previous  1 ... 17, 18, 19, 20, 21
Author Message
 Post subject: Re: "Lacewood" Amp V2.0
PostPosted: 16 Nov 2018, 02:39 
Offline
User avatar

Joined: 02 Mar 2009, 12:41
Posts: 1090
Location: Vänersborg, Sweden
Isn't the 45 an equivalent to 10Y?! I got a pair of these but I already have to 750mW amps ...

_________________
Magnus

“If you don't know where you are going, any road will get you there.”
―Lewis Carroll


Top
 Profile  
 
 Post subject: Re: "Lacewood" Amp V2.0
PostPosted: 16 Nov 2018, 07:14 
Offline

Joined: 20 Feb 2014, 10:35
Posts: 54
Location: NZ
Only in that they are both directly heated triodes, otherwise not similar. 801a is a 10y with higher ratings.


Top
 Profile  
 
 Post subject: Re: "Lacewood" Amp V2.0
PostPosted: 16 Nov 2018, 18:54 
Offline
Project Author
User avatar

Joined: 06 Apr 2009, 10:08
Posts: 1538
Location: US Pacific Northwest
lowhifi wrote:
I will like to build the Electra-Print audio 45 amp using the power supply of the Lacewood 2.0
https://www.electra-print.com/45silver.php Any worries.
Well, for starters, the Lacewood 2.0 supply has no 2.5v filament supplies, the 6.3v winding is overkill for a couple of 6SN7s, and the B+ will be quite a bit lower than the Electra-Print supply. Other than that, no worries.

_________________
Matt
It's all about the Glass!
http://www.CascadeTubes.com
Cascade Tubes Blog


Top
 Profile  
 
 Post subject: Re: "Lacewood" Amp V2.0
PostPosted: 25 Nov 2018, 13:38 
Offline
Project Author
User avatar

Joined: 06 Apr 2009, 10:08
Posts: 1538
Location: US Pacific Northwest
On the advice of someone I respect, I performed an experiment this morning. I tried out the KT-88 in this amplifier. It did have a nice sound. However, unfortunately I only have one working KT-88 currently in my possession. As such, I had to run the amp in monaural mode. But I was able to take some measurements on that channel. Here are the numbers:
Attachment:
Lacewood V2 KT-88 Summary.png

So if anyone has completed the Lacewood V2 and happens to have a set of KT-88s handy, could you give us your impressions?


This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.


_________________
Matt
It's all about the Glass!
http://www.CascadeTubes.com
Cascade Tubes Blog


Top
 Profile  
 
 Post subject: Re: "Lacewood" Amp V2.0
PostPosted: 22 Dec 2018, 20:17 
Offline
Project Author
User avatar

Joined: 06 Apr 2009, 10:08
Posts: 1538
Location: US Pacific Northwest
Suncalc wrote:
So if anyone has completed the Lacewood V2 and happens to have a set of KT-88s handy, could you give us your impressions?
Ah... No. DON'T DO THIS!

I just switched on the Lacewood V2.0 for a listen and evidently I smoked a cathode bias resistor. After doing some analysis I have concluded that this is a likely outcome for anyone trying the KT88 in this amplifier. And if you run it in Stereo mode, you'll over tax the power transformer as well.

So stick with the 6V6, 6L6, 6W6, & 6F6 for this amp. I hope I didn't lead anyone astray. :blush:

_________________
Matt
It's all about the Glass!
http://www.CascadeTubes.com
Cascade Tubes Blog


Top
 Profile  
 
 Post subject: Re: "Lacewood" Amp V2.0
PostPosted: 23 Dec 2018, 05:22 
Offline

Joined: 13 May 2016, 02:02
Posts: 109
Location: Javea, Spain
That's saved me a few euros. I was going to order some KT-88s in the new year.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 206 posts ]  Go to page Previous  1 ... 17, 18, 19, 20, 21

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: mike567 and 15 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy