DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 24 May 2018, 10:19

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: 25 Jun 2012, 16:44 
Offline

Joined: 13 Mar 2012, 16:53
Posts: 4
Hi all.
I've decided to build a pcb-based SET stereo amp. It will sit between a Cornet2 (all tube phono stage) and some 1970 ~94dB/W/m, 8-Ohm 3-ways. I rarely listen to more than 1 watt on my current amp. I think I'm down to two choices: Decware's ZEN SET Zkit1 or the Get*Set*Go board. Does anyone have enough experience with either or both of these to comment? Many thanks!


Top
 Profile  
 
PostPosted: 19 May 2017, 05:50 
Offline

Joined: 17 Mar 2017, 11:07
Posts: 12
I'm just about to start on a Decware ZKIT2 valve project.

https://galimaufrey.blogspot.co.uk/2017/05/decware.html


Top
 Profile  
 
PostPosted: 21 May 2017, 17:21 
Offline

Joined: 03 Oct 2009, 19:04
Posts: 35
Location: Austin Texas
I have built the Get set go amp.
It's a very good design and will reward well with carefully selected parts. Plus 1 on the Cornet, I have had two and am thinking about another. I have an un used board I bought several years ago.
Cheers
Ed


Top
 Profile  
 
PostPosted: 01 Jun 2017, 19:47 
Offline
Project Author
User avatar

Joined: 06 Jun 2008, 18:23
Posts: 4868
Location: Australia
http://retro-thermionic.blogspot.com.au/2015/11/el84-se-ul-power-amp-with-attenuator.html

I built Decware's EL84 amp. Meant to be a triode but I made it a SE UL amp. No PCBs just all point to point. Absolutely loved the sound, extremely good. Sold now.

_________________
Projects: "Sanctum" - 12AU7 and 6AS7 direct coupled headphone amp | "retro-Oatley 6J6" - 6J6 push-pull headphone amp with OPTs | "retro-Hiraga" - Jean Hiraga Le Monster
Website: retro-thermionic


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy