DIY Audio Projects Forum

New Member Introductions
Page 62 of 63

Author:  gofar99 [ 29 Jan 2017, 21:55 ]
Post subject:  Re: New Member Introductions

Hi Folks, welcome to the forum. There are many helpful diyers here and I'm sure they will be glad to assist. This is a friendly place..

Good listening

Author:  SteamClock [ 13 Apr 2017, 15:20 ]
Post subject:  Re: New Member Introductions

Hello from Switzerland!
I'm looking for ages to buy a tube amp, but nothing float my boat, so I started to DIY one thanks to your community.
A warm thank you for sharing all your experiences :-)


Author:  roadrunner321 [ 18 Aug 2017, 11:18 ]
Post subject:  Re: New Member Introductions

Hello from Bucharest, Romania!

I work as a Software Engineer in the telecom solutions industry, I'm 31 years old and I play in a couple of bands. I'm interested in tube amplifiers and guitar pedals, I have some DIY experience, built a few pedals and even replaced caps in my Mesa Boogie Mark IV amp. I was looking for DIY tube preamp clones, especially Triaxis/Mark IV clones and I found this forum. I hope I can find useful information, learn a good deal of useful stuff and have fun.


Author:  steakhead [ 21 Aug 2017, 18:57 ]
Post subject:  Re: New Member Introductions

I started off in electronics using a screw driver as a soldering iron, and a gas stove
to heat it hot enough to solder, I've come a long way, through my education, and later employed as an electronics technologist in a leading high technology firm.
doing work with wires is considered the most important part of the industry, so you just keep up with your efforts in this direction, and keep in mind, you can never know, to much of basics

Author:  ether_joe [ 22 Aug 2017, 09:23 ]
Post subject:  Re: New Member Introductions

Hello! My name is Sean and I'm located in Oakland, California.

My JVC car head unit is on its last lI'm interested in building a simple power amp section I can plug my phone or mp3 player into. Just need a volume knob. Might be fun to do an EQ later on also.

I'm pretty much a n00b, can wield a soldering gun but need to learn more about the raw electronics. I've been looking at kits but there's quite a range. Any suggestions on a good beginners kit?

Author:  neka_budala [ 10 Oct 2017, 14:50 ]
Post subject:  Re: New Member Introductions

Hello from Croatia, Europe, I'm new in audio stuff, I have basic knowledge of electronic from high school. I recently bought on old things market someone's audio amplifier project and would like to finish it over the winter. It would be my entry to the audio equipment world and good stress release from my job.

Author:  purwoadi [ 18 May 2018, 18:10 ]
Post subject:  Hello from Indonesia

Hi, my name is Michael from Indonesia. I'm new in DIY world though I know only a basic SS electronic from my school.
I love listening to the music, I have piano, flutte and some audiophile equipment from Rega. But from now, I will try to build those by my self. Hope I can share and get some information here

Author:  gofar99 [ 18 May 2018, 20:27 ]
Post subject:  Re: New Member Introductions

Hi and welcome to the site. There are many helpful folks here. Just ask away.

Good listening

Author:  Nim [ 18 Nov 2018, 18:15 ]
Post subject:  Re: New Member Introductions

Hi from Belgium!
I've been enamoured by tube based project for years now, but apart from messing with a simple guitar amp's EQ circuit, I never really dug in before. After stumbling across the 6DJ8 headphone amp project while browsing, I figured it was time to change that! Tinkering together my own amp seemed far more fun than just buying one.


Author:  Febrile Mech [ 29 Dec 2018, 19:52 ]
Post subject:  Re: New Member Introductions

Hi everyone
I'm Doug from Canada

My skills are limited. My interests lofty. A zany collection of components and scrap chassis you'd think I knew what I was doing. Too bad spell checker didn't make circuits.
I've been missing some good headphone sound
I ran across the IRF510 Headphone Amp, a quick check and found I have most of the parts less the mosfets.
Being into RC I'm wanting to power with a lipo pack. The voltage will be little high or low depending on which battery I use. 11.1 or 14.8.

Any more questions I have I'll put on the existing thread.


Page 62 of 63 All times are UTC - 6 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group