DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 14 Oct 2019, 11:57

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 14 posts ]  Go to page Previous  1, 2
Author Message
PostPosted: 19 Feb 2009, 22:42 
Offline
Editor
User avatar

Joined: 28 May 2008, 21:53
Posts: 4579
Location: Winnipeg, CANADA
That will work just fine. You could also run another preamp off it.

_________________
[ DIY Mains AC Power Cable Cord ] - [ Gobo LM1875 Amp Kit ] - [ Tang Band D4-1 Horn Speaker Kit ] - [ Monoblock Push-Pull KT88 Tube Amp Kit ]


Top
 Profile  
 
PostPosted: 20 Feb 2009, 10:13 
Offline
Project Author
User avatar

Joined: 06 Jun 2008, 20:12
Posts: 972
Location: Houston, TX
Alex
That will work perfectly. Nice find.
If you want less expensive try this one
http://www.antekinc.com/price1.html
AN-0512
50VA with the output you need.

_________________
DIY Lightspeed Passive Attenuator


Top
 Profile  
 
PostPosted: 21 Feb 2009, 11:03 
Offline

Joined: 17 Feb 2009, 10:28
Posts: 7
As I was looking on Digikey, I found some polypropelyne and polyester caps like gio suggested, but the .001 uF caps, of which I need 8, were about $20 a piece, and the 220 + uF caps for the voltage regulator were a princely sum of $250 a piece. I figure I am ethier I am looking in the wrong place, or I need a different kind of caps. Are ceramic ones ok.

thanks, Alex


Top
 Profile  
 
PostPosted: 21 Feb 2009, 15:16 
Offline
Editor
User avatar

Joined: 28 May 2008, 21:53
Posts: 4579
Location: Winnipeg, CANADA
Hey Alex, for the 220uF you will want to use electrolytic. What country are you in?

Here are a couple of DigiKey ideas:
http://search.digikey.com/scripts/DkSea ... e=P3901-ND
http://search.digikey.com/scripts/DkSea ... =P12383-ND

_________________
[ DIY Mains AC Power Cable Cord ] - [ Gobo LM1875 Amp Kit ] - [ Tang Band D4-1 Horn Speaker Kit ] - [ Monoblock Push-Pull KT88 Tube Amp Kit ]


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 14 posts ]  Go to page Previous  1, 2

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 8 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy