DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 23 Aug 2017, 14:28

All times are UTC - 6 hours [ DST ]

Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: 11 Aug 2017, 07:51 

Joined: 08 Aug 2017, 07:12
Posts: 2
The debate around SMPS vs Iron cored transformers in powering HI-FI audio amplifiers seems to end in favour of the switching power supplies !!

Here is an interesting example about such a debate: ... wer-supply

And here is a praiseful review of an SMPS powered gainclone:
Another one from the inventor of the gainclone himself (Thanks Mike for the precious gift to the audio community) :

You are convinced? If NO leave NOW, this thread is not for you.

Fore those who are interested I’ll show you how to modify a PC AT or ATX power supply to get symmetric output from +/-12V to +/-24V @ some Amperes (this depends on the power of the PS).

We need a PS with center tapped output transformer and a TL494, or clone ( KA7500, KIA494...), control IC. But other PSs can also be used I think.

Some facts (please correct me if I’m wrong):
- We can get up to 24V from the +/-12V rails by changing a single resistor.
- The limitation of the -12V rail is due to the used “small” rectifiers only. If we change them with “big” ones we can sink as much amperes as from the +12V rail.

There is many tutorials on the web showing how to mode a PC PS to get 13.8V. I recommend understanding this step first. ... v-dc-20-a/

and more links here:

What we need to do?
1- Change the output of +/-12V rails to the value we want.
2- Change the “small” diodes in the -12V rail by “big” ones.
3- Omit the +5V and +3.3V rails.

The final circuit which we must do is shown in the attachments.

- For L1 and L2 wind some turns of 1mm copper wire on the yellow toroidal core.
- L3 and L4 are the +12V rail inductors (you can salvage from another PS).
- 1000uF Capacitors must be rated at about 20% more than the needed V value .
- The rectifying diodes must have 50V @ 10A or more.

Choose R1, R2 values to get the needed V.

A much simpler way for rectifying and filtering is shown in the following link. Despite a simple alternance rectification and a basic filtering the author claims that the PS works very well: ... 00w-a-500w

This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.

PostPosted: 11 Aug 2017, 21:51 
Project Author
User avatar

Joined: 04 Jun 2008, 20:59
Posts: 3397
Location: Arizona, USA
Hi, I use SMPS all the time. They are just fine. I have seen the mods for using PC power supplies but they are often larger than what I am powering. With ones from several companies quite inexpensive I just buy what I need.

Good listening

Some of my DIY Tube Amplifier Projects:

PostPosted: 12 Aug 2017, 04:29 

Joined: 08 Aug 2017, 07:12
Posts: 2
Thanks gofar99 for the feedback.
Yes, the PC power supplies are "large", literally and figuratively, with relativelly big boxes and high power.
The advantage are cheap and we can find them everywhere. You live in the USA, so you can buy any thing you need, but think about those guys in the 3rd world !!
By using a moded PC PS you have double satisfaction, the joy of DIY and the fonctionnality.
How your amp sounds with the SMPS?

PostPosted: 12 Aug 2017, 06:22 
User avatar

Joined: 01 Jun 2013, 09:05
Posts: 485
I use a charge pump in my Aikido line stage.

This was trying to see what I could drive off a laptop PSU for fun.
There was no real reason to do this except I wanted to just power it from a laptop PSU using only DC into the preamp.
I used a charge pump to generate 350v and fed this into a Maida regulator. (low current) Feeding two ECC88 and two EM80.
Because of the SRPP and heater lift voltages using the same supply as the B+ I used a DC to DC converter to isolate the heaters.
The simple filter (pic) helps chop off the noise..
I have never powered a power section off SMPS but I like the line stage.
This wasn't to reduce cost just wanted to see if it worked for fun.
Some people on the net have used nixie tube B+ circuits to good effect.

M. Gregg

This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.

What is the sound of one hand clapping?

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 6 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© - Terms of Service - Privacy Policy