DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 28 Jul 2017, 09:52

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 15 posts ]  Go to page Previous  1, 2
Author Message
PostPosted: 25 Feb 2010, 10:48 
Offline
User avatar

Joined: 14 Feb 2010, 08:16
Posts: 7
Location: VIENNA, AUSTRIA
hi gio,

so do you mean, it is not necessary to connect to all three, just one of them?

thank you very much for your time, oliver


Top
 Profile  
 
PostPosted: 27 Feb 2010, 11:34 
Offline
Editor
User avatar

Joined: 28 May 2008, 21:53
Posts: 4480
Location: Winnipeg, CANADA
They will all be connected so one or all should be fine.

_________________
[ DIY Mains AC Power Cable Cord ] - [ Gobo LM1875 Amp Kit ] - [ Tang Band D4-1 Horn Speaker Kit ] - [ Monoblock Push-Pull KT88 Tube Amp Kit ]


Top
 Profile  
 
PostPosted: 12 Apr 2010, 20:39 
Offline

Joined: 12 Apr 2010, 19:55
Posts: 1
I would like to do the same with my Altec 15095A transformers. I have the exact model you have however, i want mine to be 600ohm so would i use different pins?

Thanks much!!


Top
 Profile  
 
PostPosted: 13 Apr 2010, 12:22 
Offline
Editor
User avatar

Joined: 28 May 2008, 21:53
Posts: 4480
Location: Winnipeg, CANADA
From the datasheet, you strap 3 and 4 for 600 ohms.
Cheers

_________________
[ DIY Mains AC Power Cable Cord ] - [ Gobo LM1875 Amp Kit ] - [ Tang Band D4-1 Horn Speaker Kit ] - [ Monoblock Push-Pull KT88 Tube Amp Kit ]


Top
 Profile  
 
PostPosted: 26 Jun 2017, 09:38 
Offline
Project Author
User avatar

Joined: 04 Jun 2008, 21:02
Posts: 85
Location: Philippines
Sorry to dig up this thread, how didnyour SUTs sounded?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 15 posts ]  Go to page Previous  1, 2

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy