DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 20 Feb 2018, 22:04

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 2 posts ] 
Author Message
PostPosted: 30 Jan 2013, 15:54 
Offline

Joined: 09 May 2011, 20:48
Posts: 35
Hello everyone,

My chipamp (LM3886 x 2 + LM4780 (sub)) has been going strong for about a year now. I've always had a few quirks with it though. I ran out of wire when I did the initial build so I used some really old cheap and nasty unshielded twisted pair wire for the signal. Probably not the best of ideas. I've also been getting a little buzzing on high frequencies on one of the channels.

So I bought some wire from Markertek. I got some good quality Mogami stuff and I am going to rewire the parts I skimped on.

My question is: For each wire run between different components do you attach the wires shield to ground on just the "input" side. For example, my signal comes from 2 RCA jacks to a 4PDT switch (to headphone amp and to power amp), then to subwoofer crossover board. I run wire from the crossover's INPUT terminals(where I just inserted the wire, not on the crossover's output) to the Left and Right channel amp.

So the main wire runs are RCA --> Switch --> Subwoofer crossover --> Left and Right channel.

If you didn't get what I meant with the input terminals and subwoofer thing, I'm essentially just using the input terminals to splice the wire so that I can have the signal go to the subwoofer board AND to the left and right channel.

Here's a partial drawing. Where do the cable shield grounds get attached?


This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.



Top
 Profile  
 
PostPosted: 01 May 2013, 16:34 
Offline

Joined: 30 Apr 2013, 13:24
Posts: 49
I take it that the 2 RCA sockets are insulated from the chassis?[NOT earthed to chassis] Then if there is an incoming earth from them then yes as you have shown the shields would be attached to the earth side of the RCA sockets this is to keep-radiated interference reaching the earth side of the cable
In all cases there should be no earth loops-therefore only ONE piece of equipment should have a mains earth. and that should be used for all the rest of the equipment. If possible star earthing should be used for ALL connections to the chassis .


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy