DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 27 May 2018, 14:50

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 1 post ] 
Author Message
PostPosted: 18 Jan 2017, 21:30 
Offline

Joined: 05 Aug 2016, 03:04
Posts: 4
Hello!
I am seeking to build a small drum pad that can trigger short mp3 files. Here there are a lot of specifications and I don't expect to have everything explained, but any tips on how to go about making this, what IC's to use especially, or any general help and explanation would be greatly appreciated,Thank You. -Kevin

Basically the goal is to have eight buttons that will each play a short mp3 clip when pressed.
More things that would be good are:

Press more than one at the same time

A bank selector switch that lets you chose between different sets of mp3's that will be played when each pad is pressed.

The ability to download mp3s to each pad and change what each pad will play.

A Looper to let you record short loops, play them back, and overdub (record over the last recording)

Rechargeable battery (via USB) with low battery LED indicator.

Again, I realize that these are ideals, and also that it might be easier to create a custom IC to fit the needs (If anyone knows about where and how I could do that please point me in that direction by the way). But please give me some general direction or outline of how I should go about this, and any tips that might be helpful. Here is my best attempt at a general schematic of my idea. Feel free to dismiss if it is incorrect or unfeasible. Thanks again!

I found a great chip that I think might work for my purposes,the ATTINY861-20pu. I found a project that Plays WAV files off of an SD card. Any Ideas on how to better integrate this chip with the features above? Heres the Project: http://elm-chan.org/works/sd20p/report.html
LM4910 datasheet: http://www.kynix.com/uploadfiles/pdf9675/LM49100GRX.pdf
Drew out a block diagram for a circuit with the Atiny 861, I'm just encoding each pad to binary to control the triggers on the Atiny, whitch plays .wav files from the SD card to the Headphone Amp(LM4910). The bank switch just shifts the binary number up to where I will place a different set of samples on the SD card to be accessed. ----- Problems: Can't press more than one pad at once? How do I load the firmware to the AVR? Will the higher powered PWM output ruin the Headphone amp? Haven't gotten to the looper part yet. Any help or criticism greatly appreciated!
Image
Image


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1 post ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy