DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 23 Sep 2019, 03:09

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 1663 posts ]  Go to page Previous  1 ... 163, 164, 165, 166, 167
Author Message
PostPosted: 16 Apr 2019, 00:18 
Offline

Joined: 31 Mar 2019, 18:48
Posts: 5
ILoveHiFi wrote:
You need to use coax cables for input wires, not twisted pairs as offers very litte or zero proetion against noise pick up.

viewtopic.php?f=9&t=6392&start=70
Theres also quite a few plorbems which you also may be doing which I disscussed with another dude in this thread.


Thnk you for reply, last weekend i tried something and here is results
- Replaced coax cable in input signal wire like you said - nothing change, i notice when i touch to the cable or input caps the noise go heavier.
- Then i replaced input jack cable with a coax calbe too, the noise reduce abit.
- This buzz noise complete disapear when i touch to the volume pot (which shorted to pot gnd), but in my country there have no any ground system in house, and my department on 4th floor ...
- I thought about volume pot, then i remove volume pot (left input signal with 100 ohm resistors) and yea, buzz noise gone. The only noise i can notice is small hum (maybe from my power which i reduted it by diode bridge). Buzz noise still apear when i touch to input wire or input caps. So is it all about my volume pot have bad quality ????
- Larger power caps i put to power, the hum go smaller but still noticed when source silent, the problem is i feel with about 4700uf, the sound quality gone so heavy and not clear , after few calculator i found on internet, i plan make a lc filter (3mh coil inductance and 1000uf caps) hope it will go well.
Srry for my bad english


Top
 Profile  
 
PostPosted: 24 Apr 2019, 08:03 
Offline

Joined: 16 Jul 2018, 04:34
Posts: 1
Recently completed this scheme, adding a 12V lithium battery, orange LED under the lamp for more drama and turning the lamp in parallel with the board for portability. Passing capacitors put 6.8mF. The result is very pleasing, the input signal does not distort, but makes it natural for listening. Now I cant find a power supply that does not add noise, so I only use the battery and the power supply to charge.


This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.



Top
 Profile  
 
PostPosted: 16 Jun 2019, 10:12 
Offline

Joined: 31 Jan 2015, 17:59
Posts: 9
Hi! I have build with ecc81 (I have a lot in the drawer). It is a good project. :up:
Bye.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1663 posts ]  Go to page Previous  1 ... 163, 164, 165, 166, 167

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy